Bed types
This article will describe the five different kinds of beds that our son RIP, an ALS sufferer, contended with, plus bed-related problems. Our son was diagnosed January 2018, and moved into our house June 2018 while he was still on forearm braces. As his symptoms worsened, he transitioned through four different kinds beds. He also had to go to the hospital a couple of times after diagnosis, so he contended with adjustable hospital beds, too.
Here are the different kinds of beds (see numbered photos below):
- a homemade platform bed with a simple mattress (similar to, but not the same as #1)
- a slatted bedframe with a simple mattress (similar to, but not the same brand as #2)
- a non-split queen-sized adjustable bed with remote, (#3 was the actual bed he owned)
- a split king-sized adjustable bed with remote (#4 was the actual bed he owned)
- a fully adjustable electric hospital bed (similar to #5, plus other models and brands)
Beds #3 and #4 were from the same manufacturer, and were very expensive items, so we didn’t try out any other brands after these two.

The URLs for the beds are:
- https://www.bedbathandbeyond.com/Home-Garden/James-Platform-Bed-with-Headboard/39896204/product.html
- https://www.endurancebeds.co.uk/blogs/news/what-type-of-mattress-is-best-for-a-slatted-bed
- https://www.amazon.com/Prodigy-2-0-PRODIGY2-QN-Adjustable-Bluetooth/dp/B01B8DGNL2
- https://www.amazon.com/Prodigy-2-0-Adjustable-Wireless-Bluetooth/dp/B01B8DGNMQ
- https://www.amazon.com/Function-Electric-Hospital-Advanced-Adjustable/dp/B0CZLLPYCQ
Non-adjustable beds
Platform bed
When our son first moved into our house in June 2018, he was still using forearm braces. He initially used his old platform bed (actual bed shown below is similar to the bed in photo #1 above). I designed and built this bed for our son when he was around 5 or 6 years old. We just laid a mattress on it for him.

While he was on forearm braces, he was able to get into and out of his platform bed himself, but it wasn’t easy, because the bed/mattress combo was too high. His feet didn’t touch the floor when he sat upright on the edge of the bed, so he had to slide forward after he grabbed his forearm braces.
He also had bought and tried a two-circuit inflatable mattress topper (see photo below) to alleviate pressure sores, but the mattress made it even more difficult getting in and out of bed because it added about 2” to the height. The topper also made it difficult to use a fitted bed sheet. The topper was nothing but an inflatable plastic- or rubber raft and made him sweat. We got rid of it.

https://www.vivehealth.com/products/alternating-pressure-mattress-pad
Slatted bed
I replaced his platform bed with a slatted bed frame (similar to, but not the same brand as bed #2 above) that he already owned before he got sick. (I don’t have a photo of his actual slatted bed.) His own bed consisted of a headboard with two legs and a footboard with two legs; the headboard and footboard were connected by wooden rails. To prevent the middle of the bed from sagging, a fifth support leg was mounted directly under the middle slat.
Bed risers for the slatted bed
Bed #2 turned out to be too low for him to get in and out of, so he bought a set of 4 bed risers (see photo below). They came in different heights. See a typical set of four at: (https://www.amazon.com/Simplify-Risers-Caster-Stabilizer-Perfect/dp/B079DBZ9ZV). Each of the four bed legs stood in a riser. After I stood the four corner legs of his bed on the new risers, I had to prop up the center (fifth) support leg on a wooden block because we only had 4 risers.

Adjustable beds
Queen non-split adjustable bed
Our son did not want an actual hospital bed, because he didn’t want his bedroom to look like a hospital room. He bought online the Leggett and Platt Prodigy 2.0 Queen adjustable bed (https://www.amazon.com/Prodigy-2-0-PRODIGY2-QN-Adjustable-Bluetooth/dp/B01B8DGNL2, shown in the photo below; mattress not present).

His girlfriend was living with him in our house and was a great caregiver for him. They shared the Queen-sized bed. Our son needed the head elevated as high as possible to enable breathing. Since the bed wasn’t a split bed, his girlfriend kept sliding downwards until her feet dangled off the foot of the bed.
Queen-size headboard
For the headboard, our son bought the Baxton Studio Model BSBBT6627 Queen size headboard as a separate purchase. The link is (http://www.baxtonstudio.com/baxton-studio-ginaro-modern-and-contemporary-greyish-beige-fabric-button-tufted-nail-head-queen-size-winged-headboard-20873.html). See line drawing reproduced from the installation instructions below. The headboard had to be assembled. There was an error in the instructions, which required some improvising and drilling.
Attaching brackets to bed frame
The headboard brackets were very difficult to attach to the bed frame. Because there were no wheels on the frame, I couldn’t wheel the bed out from the wall to attach the brackets to the back of the bed frame. The presence of bedrisers (discussed below) also prevented me from moving the bed away from the wall. I had to lie on my back under the bed to attach the brackets to the bed frame.
Attaching headboard to brackets on the bed frame
Likewise, the headboard brackets were very difficult to attach to the headboard. Just like attaching the brackets to the bed frame, I had to attach the headboard to the bed frame while lying on my back under the bed while using a flashlight.
Using the bed
After we placed our son in the bed, I discovered a problem. Every time our son or his girlfriend leaned against the headboard, the headboard tipped against the bedroom wall. The brackets only held on to the bottoms of the two legs of the headboard. There was no stability at all. It was very flimsy. See drawing below. I had to stuff a cushion behind the headboard to stop it from tipping every time someone leaned on it.

Head of bed
Our son needed the head support of the bed itself tipped upright as high as possible to enable proper breathing, but the upper part of the bed only rose to 70 – 75 degrees, which left a gap behind his head, so we had to position pillows behind his head to fill in the gap. I eventually had to build an appliance in my basement workshop to tilt his head even further upright than the pillows could provide.
Rusted decorative tacks
When we had originally received the Queen headboard, we observed that all the decorative tacks running down the front faces of both legs were rusted. See photo above. Our son had to have the headboard replaced.
Bed risers for the Queen bed
Our son had to specify the bed frame’s leg length at the time of purchase because they came in different heights. The legs were adjustable. After the bed was set up, the bed still proved to be too low to get our son in and out easily, even with the adjustable bed frame legs extended as much as possible. I raised the bed on the leg risers we had from the slatted bed. The photo below shows one of the supports under our son’s bed.

The bed was very heavy. To lift the bed up high enough to place the legs in the risers, I used my car’s scissors jack to crank up each corner of the bed frame one at a time so I could insert the risers!
Mechanism under the bed
The actual mechanism involved in bending the bed frame for the user’s comfort moved downward towards the floor as the head support bed was raised. (See photo below.) The hinge mechanism is obviously NOT supposed to touch the floor at all, so beware if you have to shorten the legs so the mechanism doesn’t hit the floor.
At some point in our son’s ALS suffering, the risers then proved to make the bed too high for us to aid our son. So now we had to lower the bed. I then removed the risers after jacking up each corner of the bed with my car’s scissors jack. However, even with the risers removed and the adjustable legs shortened as much as possible, the bed was still too high. I didn’t want to buy shorter legs. Now my only option was to shorten the actual bed frame legs. Having a band saw with a metal-cutting blade in my basement shop helped. I jacked up each corner of the bed one at a time yet again, removed a leg, took it to the basement, sawed off part of the leg, then reinstalled it. Four times.

Hand-held remotes for both adjustable beds
Since both adjustable beds had the same remotes (the Queen had one and the split King had two), the setup problems were the same and very difficult, so I’ll only discuss the Queen remote. Setting up two remotes for the King was double the trouble. The remotes sent signals to receivers that were mounted under the bed frames, so I had to lie on my back and slide under both beds to connect everything. The instructions weren’t even clear on how the electrical connections had to go. The electrical cords dangled from the bed frame under the bed because the manufacturer did not provide any straps. Our own vacuum cleaner snagged the cords and yanked one out of the wall receptacle. The Roomba we had kept snagging the wires also. I had to re-set up the remote after the plug was pulled from the wall and I needed phone assistance from the supplier. There are USB receptacles on both sides of the King bed.
Neither the Queen nor the King bed was height-adjustable, but we coped without that feature. That would have added additional cost.
Mattress details
We had options for the top surface of the mattress, so I told our son not to buy one with memory foam because I knew from personal experience that memory foam would make him sweat (it is just rubber and it doesn’t breathe). Placing a bedsheet on the mattress won’t prevent sweating. I also believe that the concept of making a body-shaped depression in the mattress is ridiculous because if you roll over, it takes a while for this first body-depression to change to the next one.
The still from the video for the bed frame that our son had bought showed the mattress you see in the photo below. (The video for the split-king showed only the non-split queen.) You will notice in the lower right-hand corner that the mattress perfectly conforms to the flat valley formed by the bed frame. The mattress itself has a flat valley, too.

A problem arose with the mattress our son bought for the split-king bed. The mattress was 10” thick and not flexible enough to conform to the bends in the adjustable bed frame. When the head of the bed was tilted to its max (around 70 degrees off the horizontal), a very large gap formed under the mattress. (See drawing below).

Every night when our son slept in bed with the head raised as high as possible, he always slid downwards towards the foot of the bed, like the arrows indicate in the drawing above. I didn’t realize until a year after his passing that a much thinner mattress might have conformed to the shape of the adjustable bed itself, so the valley in the mattress would have been deeper and he might not have slid down as much. Regardless, even the valley in the adjustable bed frame itself should have been V-shaped, not flattened as you see in the photo and drawing above.
Foot and leg support in bed
Our son did not like the way the foot portion of his bed raised his legs, so we kept that flat and put his legs on a large foam wedge (about 12” high) so his “knee-pits” were on the apex of the wedge. His heels hurt so much with even the slightest contact during the night, that we had to put towels under his calves so his heels would not touch anything. The pull of gravity made him slide regardless of what we tried. By the morning, his knee-pits had moved towards the foot of the bed. It was a no-win situation. For a while, we tried having him sleep on his full body sling so we could just roll in the patient lift, lift him off the bed to boost him, lower him, then disconnect everything, but the sling itself was polyester, so it was slippery, plus his skin didn’t breathe against it. Gravity was the enemy. I considered adding a footboard to the bed so we could place his feet against it to stop him from sliding, but without any muscle strength at all, he still would have just slid anyway and his legs would have just buckled.
Getting the patient in or out of the adjustable beds
Every morning and evening we used our SureHands ceiling lift with metal frame (https://www.surehands.com) either to place our son in his bed or get him out of bed. It took 3 people to do this properly. If only two caregivers were present, it became much, much more difficult. Positioning of the caregivers around the Queen was a little different from the King. The side of the King our son did not sleep on was moved out of the way so one of the caregivers could reach him more easily. See image below.

Placing the patient in the bed
For placing our son into either adjustable bed, we first raised the tilting head portion of the bed as high as possible because he slept practically sitting up to enable breathing. For the Queen-sized bed, the caregiver on our son’s right had to kneel on the bed in order to help. For the King-sized bed, the right-hand bed could be separated from the left-hand one so one of the caregivers could stand in the gap. The caregivers on his left and right had to center him on his head pillow while he was suspended in the ceiling lift frame, and also while keeping his arms from ending up under his torso (his arms were limp). The caregiver at the foot of the bed had to push and swing him towards the headboard and try to position him AND the wedge pillow so his “knee-pits” were exactly on the peak of the wedge AND get his butt directly into the valley where the mattress was bent.
The caregiver on his left had to hold his head up (he had head drop) until he was positioned in the bed. Many times, we didn’t position him correctly, for instance, if his butt wasn’t in the mattress valley to his liking, so we had to lift him back off the bed and start over again. You can see why the split made things easier for the caregiver on our son’s right. After successfully placing our son, we carefully removed the ceiling lift’s metal frame from him, and made sure his head was properly positioned. Many times during the night, all three caregivers had to respond to his call button and “boost” him back up because he had slid downwards and couldn’t breathe.
Removing the patient from the bed
To remove our son from his bed (morning and night), the three caregivers positioned themselves as before. The ceiling lift frame was positioned in front of him. Then the caregivers on both our son’s left and right sat him up, while one was holding his head up, then slid the armpit supports of the frame into his armpits, then put the two thigh supports under his legs, and carefully raised him off the bed.
King split adjustable bed
Eventually, our son bought the Leggett and Platt Prodigy 2.0 King split adjustable bed (https://www.amazon.com/Prodigy-2-0-Adjustable-Wireless-Bluetooth/dp/B01B8DGNMQ, see photo below, mattress not shown). He sold the Queen. The Split King was actually two completely separate beds. We also bought wheels for the legs so we could move the two halves apart. Separating the two beds became very important. When we had to get our son in and out of his side of the bed, my wife, my son’s girlfriend and I had to team up. One of us parted the two halves of the bed and stood between them, while a second person stood at the foot of the bed and the third on the side of the bed. This bed also came with the same poor quality headboard brackets and hardware as the Queen to attach a headboard that spanned the width of the combined beds. Because our son could not talk, I called the vendor to specify at the time of purchase what leg length I wanted.
Almost all of the issues, pros and cons discussed under the Queen bed were the same for the King bed, so they won’t be repeated.

King-sized headboard
Our son also bought a Baxton Studio Model BSBBT6627 King-sized headboard (http://www.baxtonstudio.com/baxton-studio-ginaro-modern-and-contemporary-greyish-beige-fabric-button-tufted-nail-head-king-size-winged-headboard-21465.html). The headboard had the same line drawing in the instructions as the Queen mentioned above. The instructions had the same error as for the Queen. Setting up the king-size bed was just as difficult as the queen. The King-sized headboard flopped back and forth, just like the Queen-sized one for the same reasons, so I had to stuff a large pillow behind the headboard and the wall so it wouldn’t hit the wall when someone leaned against it. The headboard was very flimsy. At least now our son’s girlfriend could sleep on her half of the bed without having to sit up all night or slide down towards the foot.
Hospital bed
We had to take our son to the hospital once or twice after he had developed head drop. He was put into two different brands or designs of hospital beds during those stays by the staff and both had ridiculously high backs like the right-hand bed in the photo below. There are hospital beds with low backs, like the bed in the left-hand photo below, but I never thought of asking to have the beds switched. The nurses saw me struggling with our son, but none of them ever offered to switch the high-back bed for a low-back one. I didn’t understand why the high-back bed was designed like that.

Low back rest: https://homecarehospitalbeds.com/product/medlite-beds-min-height-14-5/
High back rest: https://www.amazon.com/Function-Electric-Hospital-Advanced-Adjustable/dp/B0CZLLPYCQ
In order to prevent our son’s chin from dropping onto his chest, I rigged up a tether like you see in the drawing below. I made the tether from a very long strap I had brought with me to the hospital. One end of the strap was tied to the strap at the back of his baseball cap, and the other end was tied to whatever framework was convenient on the bed frame. The framework of one of the two beds he was in had some metal bars behind the raised back of the bed so I could tie the strap to it. The other bed didn’t have any convenient frame available, so it was much more difficult to tie the strap to anything. The back of his hat kept lifting off his head, so it was very difficult keeping his head upright.

Assistive devices
Bed ladder for the slatted bed
Even though the bed risers gave our son the height he needed, once he was in the bed, he still had trouble sitting up and lying down unassisted. He then purchased what was essentially a rope ladder, similar to the one in the photo below. I tied the lower end to the footboard of his bed and laid the rope ladder next to him after he got in bed. He had to grope for it in the dark when he had to get out of bed if he had to use the bathroom at night. He still struggled to use this ladder because his gripping power was quickly disappearing. He couldn’t grasp the handles well to pull himself up. He had the same problem trying to lie down.

Our son had the bed ladder in the photo above with 6 grips. Here’s a link: https://www.amazon.com/KkaFFe-Handles-Pregnant-Awakening-Stability/dp/B09C3VTBRP/
Here’s a short video showing a different model (only 2 or 3 grips) in use: https://www.youtube.com/watch?v=GfSL4LlhuYY
Bed rail assist for the slatted bed
After our son could no longer use the rope ladder, we replaced it with the bed rail assist (see photo below).

https://www.amazon.com/Home-Assist-Adjustable-Height-Assembly/dp/B071Z18CR8
Once I installed the bed rail, it was very secure because it could not move at all for two reasons:
- The two legs of the rail stood inside the frame and between the slats (see photo below).
- The mattress rested on the long horizontal part of the frame and weighed it down.
Our son was only able to use this device for a short while because his muscles were deteriorating. He couldn’t grasp the frame well to get into or out of bed, nor to sit up.

Head drop issues in bed
Because of our son’s severe head drop, he had to sleep practically sitting up with the head of the bed tilted quite as far up as possible. Initially we made a cushioned headband and tethered it to the bed frame. There was a short piece of Velcro between the headband and the strap so we could adjust the tilt of the head. See photo below of me wearing the headband (to protect our son’s privacy).

An alternative headband idea is shown in the photo below. Instead of a Velcro strap for adjustment, I rigged up a thick cord with a pair of block and tackles so I only had to pull on the loose end of the cord to adjust the tilt of our son’s head.

Our son came up with a much better idea: he wore a baseball cap that we connected with a tether over the top of the mattress to the bed frame with a very long adjustable strap. The strap kept tending to pull the baseball cap off, but it was the best we could do.
There were many problems with the two headbands and the baseball cap, the biggest one being that our son’s head tilted left and right because there was no lateral support or stability.
I finally designed and built a rather complicated gizmo that worked very well and is detailed in my website “Practical Guide to ALS” at https://www.guidetoals.com in the article “Head and Neck Support” at: https://www.guidetoals.com/head-and-neck-support/.

Bed or pressure sores
Bed sores were a constant worry because he could not move. The skin has to breathe to avoid moisture build up on the back or the torso, butt, and legs. It is important to avoid synthetic fabrics for the mattress, the sheets, and blankets whenever possible. Mattresses in hospitals and nursing homes have plastic coverings to stop bodily fluids from soaking in, but these coverings cause sweating.
Because he could not lie down at all, we could not turn him on his side, nor could we stretch his muscles while he was in bed.
Non-beds
Recliner
Because ALS made our son so uncomfortable while he was still sleeping in his platform bed and then his slatted bed, he wanted to try an old recliner we had (see photo below).

This was very trying for him because his torso and head kept tilting to one side during the night. The footrest wouldn’t stay up because the weight of his legs kept pushing it downwards until I propped it up. I don’t know if a brand-new recliner would have helped. He gave up on this idea.
Powerchair
Even after our son had bought the split King bed, he couldn’t get comfortable in it. Our son’s Quantum Edge 3 powerchair backrest could tilt completely back and the footrests and calf-supports could be extended horizontally, so he wanted to try sleeping in that. Unfortunately, the headrest was a tiny, hard cushion, with no lateral support, so it was uncomfortable and his head position was not secure. His armrests were uncomfortable, too. He quickly gave up on this idea, too.